User Manuals. Portserver Configuration Guide and Reference Manual. Cable Guide: Portserver TS, Digi One, and Connect products only. General Documentation. PORTSERVER 8/16 Datasheet. Diagnostics, Utilities and MIBs. Product support RSS feed for PortServer 8/16 (legacy) Search our knowledge base for articles related to this product.
Quick start guide, Portserver ts family series, Run wizard install
PortServer TS Family Series
Quick Start Guide
*If switch 4 is up, termination resistor
is connected.
If switch 4 is down, termination resistor
is not connected.
Set serial DIP switch (MEI versions only) according to your serial device
requirements. Pinout information available on back of quick start.
Congratulations!
Configuration is complete.
Go to the User's Guide
on the CD for more
information.
Connect
serial
device
Connect
Ethernet
cable
Connect
power
supply
Digi Portserver Ts16 Manual
Insert CD
Follow wizard
© Digi International Inc., 2006.
Digi, Digi International, the Digi logo, and PortServer TS are trademarks or registered trademarks
of Digi International, Inc. in the United States and other countries worldwide.
All other trademarks are the property of their respective owners.
Software &
Documentation
Software &
Documentation
PortServer TS 1 MEI (shown)
PortServer TS 16 MEI (shown)
Connect
Ethernet
cable
Connect power cord
and flip power switch on
If you have a UNIX system and it
does not use an auto-mounter, you
will need to manually mount the CD.
See the back of this guide for UNIX
specific instructions.
Connect serial
devices
Connect
Ethernet
cable
Connect
power
supply
PortServer TS MEI
PortServer TS P MEI
PortServer TS H MEI
PortServer TS
What you will need
PortServer TS 8
PortServer TS 16 MEI
Ethernet cable not included
The PortServer TS 8/16 MEI settings are configured
through the software. Complete the Quick Start Guide
and go to the User's Guide for the procedure to
configure the MEI ports. The ports are set to EIA-232
by default. If your device is not EIA-232, configure the
MEI settings immediately after completing the Quick
Start. The default settings will not harm your device,
however, we recommend configuring the MEI
settings immediately as a precaution.
*If you need help
with cabling,
see other side
Connect serial devices
1
2
3
1
2
3
1
2
4
RUN
WIZARD
INSTALL
8 or 16
Port
INSTALL
1, 2, or 4
Port
3
Be sure to check Digi Support for
the latest firmware updates at:
http://support.digi.com
1 2 3 4
*
In EIA-232 mode, If switch 3 is down,
9V power is provided on pin 9 (DTR).
If switch 3 is up, power on pin 9 is disabled
and 5V power can be enabled on pin 1 (RI)
through the software interface.
Note for PortServer TS P MEI series only -
Power (green)
on; power supply
LEDs will flash
during startup
Power
- steady blinking; seeking or
waiting for an IP address
Link
- on; physical network detected
10/100
- off; 10Mbit Ethernet detected,
on; 100Mbit Ethernet detected
ACT
- on; bad initialization,
off; ready,
blinking; network activity
COL
- on; Ethernet collision detected
LEDs will flash during startup
Up/On
Down/Off
EIA-232
EIA-422/485
Full-Duplex
EIA-485
Half-Duplex
Switch
Settings
*
1 2 3 4
*
Status (yellow)
blinking; seeking or waiting for an
IP address - for status codes, see User's
Guide
You must disable
firewall/antivirus software
before running wizard.
!
Power cord
(PortServer TS 16
families only)
Wall and brick power supply
(PortServer TS families 1/2/4/8
only)
Digi Portserver Ts 16
DB-9 -RJ-45
adapter
PN:(1P)
B
90000687-88